Zenkina, Olena

The generation of polymer brushes by surface-initiated polymerization techniques has become a powerful tool for the creation of hybrid materials. Governed by the type and amount of polymer used in the modification, the chemical and physical properties of a surface can be tailored by polymer grafting. In this study, a commonly used polymer flocculant, polyacrylamide (PAM), was grafted onto the surface of activated carbon (AC). This hybrid material was designed with the intent of combining the functionalities of both the activated carbon and the polymer flocculant, potentially acting in a synergistic manner. The PAM grafted AC (AC-PAM) was examined as a flocculant in the treatment of mature fine tailings (MFT). AC-PAM was synthesized by surface-initiated activators generated by electron transfer atom transfer radical polymerization (SI-AGET ATRP). This was accomplished by pre-functionalizing the surface of activated carbon by oxidation, followed by the attachment of an ATRP initiator. From this surface, SI-AGET ATRP of acrylamide monomers was performed. The resulting AC-PAM was characterized by FTIR, XPS, TGA, SEC, and BET analysis. Characterization results indicated the successful grafting of polyacrylamide from the surface of activated carbon. The AC-PAM was measured to contain approximately 10.6% PAM by weight, and the average-number molecular weight of the grafted polymer was 176,100 g/mol. The flocculation performance of AC-PAM and PAM were compared by performing settling tests with 5 wt% MFT. The optimal polymer dosage for PAM was found to be 10,000 ppm, producing an initial settling rate of 3.51 m/hr and a supernatant turbidity of 430 NTU. Comparatively, the optimal dosage for AC-PAM was found to be 20,000 ppm, producing a supernatant turbidity of 114 NTU and a fast initial settling rate of 27.54 m/hr. The improved flocculation performance is hypothesized to occur due to the effective increase in the molecular weight of PAM when grafted from the surface of activated carbon. In all, our work demonstrates the successful grafting of PAM from AC, as well as potential wastewater treatment applications for these types of hybrid materials.

Author Keywords: Activated carbon, Atom transfer radical polymerization, Flocculation, Grafting, Polyacrylamide, Surface-initiated polymerization

The synthesis of biaryls through transition metal catalyzed cross-coupling reactions has been instrumental for synthetic organic chemists. The Hiyama reaction, which features organosilicon derived cross-coupling partners with aryl chlorides, remains relatively underdeveloped compared to other cross-coupling reactions. In this thesis, it is demonstrated that bench stable Palladium N-Heterocyclic Carbene (NHC) precatalysts of the general type [(NHC)Pd(allyl)Cl] are highly active in the Hiyama cross-coupling of activated aryl chlorides with low catalyst loading. Notably, this research demonstrates that catalysts featuring sterically less demanding NHCs display higher activity in this reaction, which contrasts with other cross-coupling reactions. Preliminary mechanistic investigations including in situ reaction monitoring by 19F NMR spectroscopy have uncovered side reactions. These side reactions may explain the low catalytic performance observed with unactivated substrates. These studies could help to further develop this reaction and improve catalytic performance. Additional investigations have also been made into ligand development by altering the electronics of sterically hindered NHC ligands for use in other cross-coupling reactions.

Author Keywords: Catalysis, Cross-coupling, Organic Chemistry, Organometallics, Side Reactions, Synthesis

This thesis describes the synthesis, application and evaluation of a UV crosslinked 3-methacryloxypropyltrimethoxysilane-derived coating formulation. This is a two-component sol-gel system with 3-methacryloxypropyltrimethoxysilane (MaPTMS) and tetraethoxysilane (TEOS). Herein we show that if we change the co-solvent required for solubilizing MaPTMS from the more common methanol and ethanol to isopropanol we change the rate of hydrolysis from days or weeks to minutes. With the assistance of 2D 29Si-NMR we demonstrate that the system undergoes extensive condensation in twenty minutes. Using standard UV irradiation, the material can be extensively UV crosslinked with 70% of the methacryloxy functionality being consumed in 5 minutes upon irradiation in the presence of a photo-initiator. When this material is used to coat low carbon steel and immersed in an accelerated corrosion solution (dilute Harrison's solution); this material affords low carbon steel 25 hours of protection when crosslinked and 17 hours of protection when uncrosslinked.

The material was then used to encapsulate polyaniline (PANI), an intrinsic conductive polymer used in the corrosion protection of metal substrates. PANI has been encapsulated previously in sol-gel material, but due to the pH dependence of the solubility of PANI, it can not be encapsulated in more commonly chemically crosslinked sol-gel. As our system is UV crosslinked rather than chemically crosslinked, we were able to successfully demonstrate the inclusion of PANI into our coating system.

Finally, this thesis includes a thorough computational investigation into the structure and band gap of PANI. Through the analysis of the band gap it was shown that the structure of the polymer commonly displayed in literature is not the correct structure of the polymer. Our results suggest that when PANI is made electrochemically, the oligomer contains two quinoid units next to one another instead of the more usually represented regularly alternating benzoid and quinoid units. The results also suggest that when PANI is made using the oxidant ammonium persulfate, the polymer most likely contains a Michael adduct structure somewhere in the polymer chain which dominates PANI's electronic properties.

Author Keywords: 3-Methacryloxypropyltrimethoxysilane, Computational Chemistry , Corrosion , Polyaniline, Tetraethoxysilane